Tuesday, December 20, 2011

Drill Bits and Dynamite Part Nine

That's all good and fine, except that there are no drill bits and no dynamite in this story. There are however.... trees falling out of the sky. That'll just have to do for now.

This is back on the Sea to Sky project again. Cut 10 was in full swing with drilling and blasting operations. The tree fallers were working up above on the nasty Cut 9. I was in the parking lot above the Cut 10 job and started to notice that the traffic was starting to slow down and bunch up. On this narrow ribbon of highway it was always a sign of a problem when the traffic did this. It got to the point where there was no north-bound traffic at all. A minute later, south-bound ground to a halt. I called on the radio, asking if anybody knew what was up. It could be a broken down vehicle, one of our trucks dropped a rock...anything out of the ordinary would do it.
 One of the guys called back, yelling gibberish at the tip of his lungs.
 I asked him to repeat, so that I could understand him.
Same thing, high intensity, garbled, yelling guy.
I tried again, I asked him to slow down and tell me what was going on.

"A...tree....hit....a....car.

I have no idea how that can happen, but I would imagine it's not a good scene. With traffic at a stand still, I walked/ran a short distance past all the traffic to the site of all the chaos. When I arrive, there it is....a big tree smashed on the road. Branches all over the place, shards of wood all scattered about. A little ways south of the tree, is a small car with the side all pushed in. A very shocked driver is wandering around, being tended to by workers and other drivers.

What happened was this. The fallers were working right up at the top of the right of way on Cut 9. They had been working there for a couple of weeks, no issues. The expert tree cutters had been laying the fallen trees across the slope, to keep them from sliding down the step side-hill. This one particular tree took a bad bounce when it fell, and turned down-slope. The steep ground and slippery branches turned the tree into a toboggan. The tree faller could do nothing but watch, as it gained speed and slid down through the treeline. It slid under the Hydro power-lines and rocketed past the standing timber. When it got to the rock bluff above the highway, it had enough speed and momentum to absolutely clear the north-bound lane.
 The tree/rocket speared some poor shmuck driving south in his Honda car. One moment he was driving along listening to Willie Nelson, and the next he was trying to control a car that just got hit broadside by a flying tree. Our man was really lucky that the tree didn't insist on coming in through the drivers window. It hit just behind and below it . His lucky moment inside of his shitty day.  There was no one else involved, all the other drivers were in the clear.
The aftermath...cut up and pushed off the road



Lucky that the tree hit here....rather than right through the drivers window

The impact blew out side window....can you imagine the shock of having a tree fall out of the sky and land on your car!


The police and fireman rushed to site, but there was nothing to do. Take statements, unsnarl the traffic and make sure that everyone is safe. The tree faller drove down to the site to see what happened, and to apologize to the driver. It was just one of those things, where the luck and planning ran out. No blood, no injuries...just shock and a hammered up car.
The path of the tree....it slid all the way from the top of the right of way....estimated to be approx. 600 feet!
Getting the traffic unsnarled

The fallers truck...he came down to see if everyone was OK....kinda brave actually.


The driver of the car, wearing the blue vest

The driver, policewoman, and Rick Berg..... the Segment One project manager for Kiewit

The damaged car on the flat-deck truck, the fallers pick-up truck, and a rock truck waiting to get out.


So....the last part of the story goes like this.

I thought that this little incident was going to turn into a lawsuit. I called up my helicopter buddy Robin, to see if he was around. As it turns out, he was just finishing up with a Hydro contract. He was about 30 minutes away, and had time and fuel for a bit more work. My idea was to go up and photograph the the whole site from the air...for the official record. The free ( for me ) helicopter ride was the added bonus.

Now here is where the story gets a little sticky. Robin was going to land in the construction office yard at Westport pit. The safety guy for the whole project, Ross Taylor was there. At this point in the job, Ross had rubbed me the wrong way on one particular incident...so I was kind of pissed at him.  He asked if I was interested in driving up to the site where the fallers were working. I said no thanks. ( I'm fairly sure that I forgot to tell him that I had a helicopter coming ) Ten minutes later, Robin touches down in the yard. I load in a couple of deserving co-workers and fly up to the area where the tree started it's journey. On the way in towards the site, we spy Ross walking in through the trail. I got Robin to move in closer and lower, so that we could wave out the window at Ross. ( I know what your thinking, I agree ) I took some photos with my lo-res camera, got shots of other nearby sites of interest .
It took three or four years for the case to go to court, the photos were never used.

So here is the deal at the end.
Ross Taylor and I became friends a while after that. He invited me to speak about blasting techniques at a conference in Squamish, and was good about helping me to manage my safety program.
Ross, if your reading this, consider this my written apology for being a dickhead that day. I owe you dinner and many drinks. We'll order fresh booze every ten minutes until one of us falls out of our chair, and then every twenty minutes after that. Call me.

Monday, December 19, 2011

A Boy and His Cars

Could a young man who was photographed extensively like this....not end up... ass deep in a love affair with hot rod cars and classic automotive iron?
That'd be my dad, me and my Aunt Grace at Mission BC
The 57 Chevy wagon.
I bought this car when I was fifteen years old, in 1975. I had some money saved up from chores and neighborhood lawn mowing, and my grandmother kicked in some birthday cash. I paid two hundred bucks for a rolling shell of a car, with a non running small block engine.
 The guy who owned it previously had been killed in a car accident while street racing. He was barreling down a quiet rural road, in a race with another car, when a lady pulled out of her driveway. With few options, Larry steered into the trees on the left hand side of the road. With no seat belt, and in a piece of crap car, in a high speed crash...he did not survive.The 57 wagon was a project car that he was working on at the time of his death. I bought the car from his parents some time after the crash. Even at that point, I remember it as an awkward moment in their driveway, the look on the mom and dad's faces. They looked lost, defeated and profoundly sad.
  There was another weird connection that I had forgotten about. The tow truck driver, that dragged my new purchase home, would go on to be killed in the crash of a gorgeous 55 Chevy wagon/straight axle street car.
 There seemed to be a lot of automotive carnage back then.

Starting at fifteen years old, I started to work summers and weekends at Jackson's Bros Logging in Wilson Creek. I was the mechanics/welders helper and chief floor sweeper. This paid union chokermans rate, and for a young guy with a project car, it was a great source of badly needed cash. I bought several of Petersens Automotive books on small block Chevy engines and a few on body work techniques. I studied these feverishly to try and get a handle on what I needed to do. I also gulped down the latest and greatest from the hot rod magazines, Car Craft and Hot Rodder.

 Several people and events lined up in my favor. My mechanic friends at work helped me to unlock some of technical puzzles. My high school auto mechanics teacher, Mr Ayles was an ex-General Motors instructor, so he was a great resource. Two of my schoolmates had a wonderful collection of engines and still boxed hi-performance parts, and they needed money more than they needed the parts. So I ended up with a partially built 327 and a box full of cam kits, aluminum intake manifold, Hooker headers and some reasonable heads.
Feeding my thirst for speed and power...Seattle Raceway "64 Funny Cars" event...mid 1970's...the Holy Grail of noise and acceleration ...Hmmm....breathe those nitro-methane and ethanol fumes in


By some miracle and a lot of cursing and swearing, I managed to swap camshafts and other miscellaneous parts into the 327 block. I did this right in the driveway of my parents house. I kept the engine on a home made stand and covered it in oily rags and then a tarp when I wasn't working on it. I paid through the nose for other parts by shopping at the local auto parts store and selecting items from their "special" catalog. Things like flex fans, yellow Accell spark plug wires and fancy chrome air cleaners were like gold.



The idea for the front spoiler came when I had removed the front bumper assembly to chase some rust away with brazing and Bondo. When the front end sat there without all the heavy chrome and steel hanging on it, I decided to go for the custom look. Being heavily influenced by drag racing ( going to Seattle International Speedway as a spectator since I was fourteen years old ) having a lighter front end was a good thing.

I made the curved fender extensions in metal work class and then riveted and brazed them on. A piece of mild steel, about 3/4 by 3/16 spanned the two extensions. Then, not having a lot of custom body work experience ( OK ...none ) I covered the framework in masking tape several layers deep. Over this, I laid several layers of fiberglas cloth and matting....over that, went the filler to cover up the imperfections. All in all, it looked pretty cool...I don't recall ever seeing a similar treatment on a "5 6 7" car.
 I built the hood bulge myself in a similar "glass over frame" style...this was in anticipation of a high rise manifold and two fours set-up that never happened.

The original car had full glass windows all around. I loved the sedan delivery look, so I cooked up a plan to achieve that. I removed the rear side glass and used them to make sheet aluminum copies. These got riveted and glued into place. And Shazaam! the sedan delivery look.

The entire brake system was replaced over the period of about two years. Every steel and rubber brake fluid line, master cylinder, shoes and drums, springs and retainers...all new.

While the car was getting built, my friends and I would get beers ( I have no idea where they came from ) and sit in the car that was on jack-stands. I had installed a Craig PowerPlay cassette deck, amp and Jensen Triax speakers...all the hot stuff of the day. We would listen to Steppenwolf, Nazareth and the Rolling Stones, drink beer and make brave plans for our lives. On occasion, I would start the open headered, cammed and over-carbed 327, right there in the driveway...up on the jack-stands....and just listen to the rumble/crackle and pop of the un-muffled engine. And you know, this was right outside the kitchen window and no one said a thing...my dad didn't freak out and the neighbors never complained
I feel like I put about 22 million cans of Bondo on that thing over the length of the project. I would lay a coat on, and then sand and grind the whole works off. I was trying to get the "perfect' finish...and that wasn't going to happen because I didn't know what the fuck I was doing. I had all the right tools and all the books...but no obvious talent for being a autobody man.

I re-did all the wiring myself...all the engine, gauges and lights. I melted the the whole system at least 3 times in the process.


The hood flew off on a test run one day. I removed all the original hood latch gear, and just used hood pins instead. I left the pins out on this day...because it wasn't meant to be a high speed run. But...the engine tuning worked out so well that it became necessary to do a hard launch and then hit second gear real quick ( 4 spd manual trans ) this violent lurch spit the hood right off and into the ditch. As me and my buddy were trying to fit the hood back onto the idling, open header car...the cops drove by. We were screwed in so many ways, I couldn't even count them.The two policeman drove by... staring out of their patrol car and never even slowed down. I have no clue what they thought we were doing, but whatever it was didn't interest them. ( they would make up for that day in later years )
My 57 wagon behind my parents 56 4-door that became mine a few years later for a thousand bucks....notice the funky fit of the hood in this photo after it got launched into a ditch.

The 57 wagon project lasted for three years, from fifteen to eighteen years of age. All told I had about 3500 to 4000 bucks into it...including the 22 million cans of Bondo. When I was eighteen and out in the world working, I bought a 68 big block/4 speed Roadrunner. The 57 project fell out of favor when the big black "Nasty" came home.
I tried to sell the 57, but no decent offers came in. One weekend, I made the decision to abandon the wagon all together. I removed all the running gear and hi-perf parts, the stereo, electric fuel pump, doors, front glass,gauges...everything. I had the remaining body towed to the dump on dollies. When it got to the dump, I set about kicking the crap out of it, leaving no panel un-dented.

 My teenage thinking was this...if they weren't going to buy it from me...then they bloody well aren't going to get it for free at the dump.

The engine got sold and went into bitchin' little Chevy II, the trans and hi-perf clutch went into a nice 68 Camaro, the wheels and tires went on a 57 two door coupe.

Sunday, December 18, 2011

Drill Bits and Dynamite Part Eight.....more Cut 14 Tales



Cut 14 is the area that was featured in the "Helicopters and Dynamite" story. This section of work was at the very north end of Segment One of the S2S Highway project. It featured very tall, steep rock bluffs that had to be sliced and diced to make room for a wider roadway.
 This requires that we as the blasting crew have to do "pioneering" work, to get up on top of the rock features, so that we can drill down vertically for the actual cuts. In some cases, horizontal blast holes ( lifters ) can be used to minimize trail building, but it is extremely hard to control lifter shots. Lifter shots create lots of unpredictable fly-rock, more vibration and more noise than properly planned vertical hole shots. ( we did use lifter shots on Cut 9 and 10, when there was no alternative....and nothing to hit with the fly rock )
330 Cat excavator up on a pioneer trail that's only as wide as the machine. Placing blast mats on to a prepared shot. This is Cut 14...looking south. Power-lines and fiber-optic cables close by. Active highway right below.

The traffic rules on when we could stop cars and for how long...varied greatly. It depended on time of day, which day of the week, pre and post holidays and of course the holidays themselves. Some days we were allowed NO stops. None. On other days it could be from 2 to 20 minutes, with 1000 dollar per minute fines for running into overtime. During the slow season, we could close the highway at night for two separate closures of two hours each...for a four hour total ...with a one hour opening in between.

 We would push as hard as we could to get work done in smaller windows of opportunity than I would have ever imagined. The upper bench at Cut 14 was so narrow that the excavator didn't have enough room to spin around. Every time that it needed to reverse, one of the blasters would have to guide him back with hand signals and radio calls.

As a lot of the work took place at night, this operation, high above the road on a narrow ledge was a little hairy at times. Each blast mat had to be carried in along this ledge, and the operator guided back each time. Six or eight mats, six or eight trips back and forth. If we were in a really shitty/risky spot...then we could only move the machine and mats in a traffic closure, to minimize the chance of dropping something on a passer-by....like a 7000 lb blast mat, or a 90,000 excavator.
Hanging the blast mats on steel pins that we installed using the reach of the hoe-drill. In this pic, you can see one of the rock-scalers up in the tree line. They would rappel down on ropes to attach the blast mats to the pins, working closely and carefully with the excavator operator. The hoe is going to stay in place during the shot to keep the mats and rocks from flying into the power-lines and fiber-optic cable.
 The whole trick of doing the blasting in this area, was to put the correct amount of explosives into the shot. Just enough to get it to break and fall away from the wall, but not so much that it launches across the road and tears out the power-lines near-by.

 We controlled this part by only using two blasters to do most of the work here. They knew the "recipe" for success and could be trusted to do the right thing time after time. We also took a team approach on the higher risk stuff and consulted with each other to get a clear view of which techniques were working best at the moment. ( as the rock conditions change, the drill pattern, explosives load, detonation timing and mat protection all changes with it )

Looking north towards Ansell Place/Seascapes

The excavator heading out to the end of the bench...once there...the bench is actually narrower than the machine, and the tracks hang over the edge.
When it came time for a blast, the traffic people would close the highway They would tell us what the last car coming through was, and when it passed and was clear....push the button...boom. It all collapses to the road below...and the loader rushes in to remove the debris within the allotted time of the closure. It's possible, when everything goes well, to do a shot...and clean it up...in five minutes. It's not pretty, but it can be done.



Whatever material that stays up on the bench, has to get swept over on to the road for the loader to pick up. The excavator has very little room to swing before it rubs the rock face. Usually a spotter would work with the operator to keep him safe.

Night work at Cut 14 was very exciting. It was winter, bitterly cold and wet. Working on a narrow bench under tower lights and the lights of the hoe. One night we had an especially tall, chunky blast to do. The volume of rock that was going to come down was fairly big. The height of the shot above the road, meant that it was going to splash all over the place when it came down. This in turn meant that big pieces could rocket into the power pole across the road...or worst case scenario...send the mats flying through the air, and into the wires ....all of this is bad stuff, and doesn't look good on anyone's resume.
Video here of cut 14 blasting with bast mats....then on to Cut 5 pre-shear shot

 So...on this particular night, we drilled gently and loaded conservatively....only a couple mats could be hung on the shot, we didn't have the ability to reach any further. The end result was a good shot...except for the huge chunk of rock that landed on the highway. The good news is that nothing flew into the wires or pole...the bad news was that a massive rock was laying in the road at 3 a.m.

Working up on the Cut 14 bench on a winters night....the path is narrow...and tall rock face on the operators side...and a nasty drop to the road on the other side. The blaster and operator have to work together to keep each other safe....bad things happen when that doesn't work out.

Placing blast mats at night...hauling them down the path one at a time.


I'm pretty sure that this was the coldest/crappiest winter that I spent in the blasting biz....just looking at this picture, makes me feel cold and wet.

And there we are with a massive boulder sitting on the highway. The 450 John Deere excavator (a large one for the uninitiated)...struggled to move it.

We tugged and pulled while the front-end loader cleaned up the the smaller debris. In the end...we had to get the front-end loader to push on the rock, while the hoe hoe pulled. We dragged it to a spot where we could get it off the pavement. It was later drilled and blasted into more manageable pieces. We did leave some pretty nasty divots in the road surface...both from the blast rock landing on the road, and our dragging the big boulder away.

The 450 Hoe, driller/blaster Mike Trufanenko and the rubber tired loader....all ready to give a heave-ho on that stubborn hunk of rock
I was amazed at the residents in the Seascapes development..... They never once complained about the noise of our work...really right outside their windows. We worked all night long with rock drills, hydraulic breakers and the constant bleeting of back-up alarms. Some of the blasts took place at one, two or three in the morning...and were fairly loud, and hit pretty hard. Not one person said a word. The only thing that pissed them off was if we left a mess, or marks on the blacktop of their driveway...then we got an ear full.

Thursday, December 15, 2011

Sea to Sky computer mock-up vs the real drive through

From the south interchange ( Upper Levels Highway ) to Ansell place....pre-construction computer mock-up of the finished highway....and the real thing...side by each

Sea to Sky Blasting Video

">Here are a few blasting videos that I recovered from an old disc. There are more images that just need to be recover and processed...it'll just take time. The link is at the bottom...

 The first video is at the Cut 10 area, beside the highway. We put the excavator bucket over the shot to keep the blast mats from flying into the air...and into the fiber-optic line...or over the bluff and down 100 feet.


The other shots are a Eagleridge (Cut 4 )...one of the small ones is a bit of a dud...where the shock-tube got broken when the blast mats were put on. It's called a "cut-off".....not dangerous...just a piss-off ( it takes a ton of time to re-attach everything...and put the mats back on.


The larger Cut 4 shots...are only matted on the Upper Levels Highway side...to control the amount of fly-rock coming over that way. The highway was closed by our traffic control people also, as an extra precaution. Some of the larger shots ( which I hope to post soon ) actually used no mats...or very few. Some of the larger/deeper shots behave better than the smaller ones.The last quick, little clip is of an 11,000 cubic meter blast on the north side of Cut 4....the seismic jolt was strong enough to bounce the 50 ton machine that we were hiding behind.
">Click the link below for video

http://youtu.be/xGjPTcn1vGA

Sea to Sky Forest Fire

I've been wanting to write this story for ages. It's about the road construction workers response to an early morning forest fire that was accidentally? set by a fellow that lived in the bush beside the jobsite. Before I get into that, I'd like to thank my photographer/writer friend Deyna . He recovered the lost video footage from an old disc and made it usable for this blog entry.
Here is a photo of Deyna when I asked for his help..
But then ...things got better when I told him how much I was willing to pay

Then I added the fact that the people involved in the fire response...would really appreciate his efforts....well...that changed everything..
 Deyna was so thrilled with the deal that he told his buddy Jack, the great news...Jack was over the moon with delight at his friends good fortune..
The story...for real this time.
 When we started the work on the new section of highway, there were several people living in the forest..."off the grid."  Some were ordinary homeless types, who found peace and safety in the forest, not too far away from civilization. There was likely a few that lived in the bush to stay close to their cash crop. We didn't interfere with their existence, and they didn't bug us. The fire in this story, started at the camp of one of these people.
This aerial photo was taken long after the fire...the construction has progressed quite a bit by the time this was taken

 This happened on a summer morning. We were on early shift, because of the heat and the increased risk of a construction activity caused fire. At the beginning of the shift, we all rallied at the Eagleridge parking lot in the dark/twilight of summertime 4 a.m. Our drilling/blasting crew were going to be working in the upper Cut 4 area, and the earthworks guys were ahead of us, doing the "clear and grub" ( stripping off trees,stumps and dirt ) at the general area of Cut 5.  I really, really wish I had a recording of the next bit of the morning. The work radio crackled with one of the machine operators calling another, and asking..
"Do you smell smoke?" 
" I don't smell anything" came the answer back
" I thought I caught a whiff of something"
" Like a machine on fire or what?"
" No man , like wood....it was wood smoke." 
Then it was quiet for a bit...then someone else got a whiff.
"Yeah, I'm smelling smoke over here, just a bit...but it's for sure wood smoke"
I called over on my radio..
"He can you guys see anything going on?"
"No..we are still in the bush here...it's too dark"
Another machine operator called out.
"Hey guys, I've got a strong smoke smell over here, the wind must have changed"
One of the other forward working guys called back.
"OK, I'm coming over to have a look, I think there's something smoldering out here somewhere"
After getting directions the location, the worker drove to the site. By the time he got there, the sun had come up enough to provide a bit more light into the dense forest.
The radio speaker nearly exploded in my hand..
"Hey!...we've got smoke everywhere!....somethings on fire! "
"Where are you guys?"
"There's thick smoke pouring through the trees....holy shit man...the bush is on fire here somewhere!"
"Where are you guys at?"
"Black Mountain Trail.....half way up"
"Where's the smoke coming from?"
" Don't know, can't see yet"
All the workers on site bail out of their jobs and head towards Black Mountain Trail. One of the machine operators, Kent heads into the bush to track down the source of the smoke. It's a difficult uphill slog through dense underbrush to make headway.
Out of breath, he calls on the radio....
"It's on fire!...the bush is on fire!...I see flames ahead...it looks like it's growing...I can see flames!...maybe 50 feet across....up on the hill...."
Kent's brother, Dean went to get our on-site water truck...which was parked nearby. Others went to get more fire hose and piss-cans ( water canisters on backpacks with pump nozzles) The water truck was set up and hoses reeled out through the bush...and pulled uphill towards the fire.
Click link below for the video 

http://youtu.be/5msnDXRWQYI   

Click link above for the video
Looking up the hill towards where the fire is burning


Pulling fire hoses uphill...in the dark...towards the fire

I can't tell if that's Dean or Kent....at the water truck on Black Mountain Trail

One of the first responders in the bush...before the sun came up.
Taking pictures in the dark....pulling hoses through the forest...uphill to the fire.


Several men were on the fire hose to knock down the biggest section of the fire...and others were draining piss-cans as fast as they could pump them. I made calls out to the guys in the office to get the fire department out to help us and take over. If I remember correctly, there was a bit of fuss over whether or not the local firemen would attend, or if the official forest fire people needed to be called in.
 The construction workers absolutely threw themselves at the task of bringing the fire under control. The water truck was drained of water, at just about the point where the main body of flames were extinguished, lucky for us. ( it would have taken about 45 minutes or more to re-load the truck with water) All the water filled piss cans on site were brought in and emptied against the remaining flames. As you can see in the video, a huge amount of work went into chasing the fire that was under the moss and deep into the ground. It was the first time that I had seen with my own two eyes, just how hot and stubborn a fire can be...while remaining relatively invisible.
 Just about the time that all the drama and hard work was over, the official fire fighters arrived to take over the mop up duties. They brought more tanker trucks and fresh bodies to make sure that this thing was really out for good. We let them hook up to the hoses that we had strung out through the bush...and I think even left one of our gas-powered water pumps for them.
 In the end...all the guys who participated in the fire fighting, felt great, felt like they really contributed to something....felt alive.
The company responded with ....nothing.
 No recognition...no "thank-you's", no letter of praise....not even a voucher for a cup of Tim Hortons coffee. They make such a big deal out of finding fault and deficiencies in things, that they are not geared for recognizing great personal effort, of going "above and beyond"....not clued into how far a pat on the back can go. ( this is where I lose thousands of dollars of future construction work, for criticizing the "big dog" )

Well maybe in the future, the "big dog" will learn to treat it's people better....and in turn get better people....who then do better work. Radical concept I know....Although being arrogant and abusive is probably cheaper and looks better on the books....obviously, burning through employees like they were firewood...works very well for them.
....and that my friends is how to keep from getting hired back to a mega-corporation....

The final pieces of the story...the North Shore News reported that the local fire department had successfully fought a blaze in the forest ...no mention of the efforts of the construction crew.

We never did see or hear from the resident of the camp again....I don't know whatever became of him

Rooting out the last stubborn bits of the fire

These are the aforementioned "piss-cans"....filled with water and hand pumped

Investigating the squatters camp

One of the official fire fighters on the scene later in the morning....this is the area where the fire originated...and then took off....up the fir tree and through the underbrush

">n>